Curing Behavior of Resorcinol Formaldehyde Resin Adhesives in Mangium and Pine Woods Bonding System under Various Curing Times

Eka M. Alamsyah, Masaaki Yamada, Kinji Taki

Abstract


Effects of room-temperature curing time on the curing behavior of resorcinol formaldehyde (RF) resin adhesives by using thermo mechanical analysis spring method in relation to the mangium (Acacia mangium) and pine (Pinus merkusii) woods bonding system were examined. Total amount of liquid resin adhesives that inserted into the small wire spring was 10 mg for each curing time parameters. Results showed that the curves of modulus of elasticity (E’) from resin adhesives that cured for 1 month, 2 months and 3 months was almost flat from room temperature to 200°C. By far E’ curve of resin adhesives that cured for 3 months did not changed and adhesive predicted had cured completely. Results further showed that in A. mangium and P. merkusii bonding system all laminates bonded with RF in room temperature at least 1 month curing time is required to meet high bond strength with minimally 60 percent wood failure as one of requirements of good bonding performance classification.

Keywords


Acacia mangium; bonding system; curing behavior; Pinus merkusii; resorcinol formaldehyde

Full Text:

PDF

References


Adachi K, Taki K. 2007. Curing behavior of wood adhesives and bond quality. Di dalam: Curing temperature of resin and methods and assessment of curing process. Osaka: Science and Technology press. Pp. 175-187.

Alamsyah EM, Liu CN, Yamada M, Taki K, Yoshida H. 2007. Bondability of tropical fast-growing tree species (I)- Indonesian wood species. J Wood Sci. 53(l): 40-46.

(JAS) Japanese Agricultural Standard. 2005. JAS No.235 for Structural Glued Laminated Timber. Tokyo: The Ministry of Agriculture, Forestry and Fisheries of Japan.

Liu CN. 2005. Bond quality of moisture curing polyurethane adhesives (in Japanese). [Thesis]. Shizuoka: Faculty of Agriculture, Shizuoka University.

Mizumachi H. 1973. Activation energy of the curing reaction of urea resin in the presence of wood. Wood Sci. 7(4):14- 18.

Mizumachi H, Morita H. 1975. Activation energy of the curing reaction of phenolic resin in the presence of woods. Wood Sci. 7(3):256-260.

Pizzi A, Stephanou A. 1994. Phenol formaldehyde wood adhesives under very alkaline conditions, part I: behavior and proposed mechanism, Holzforschung. 48(1):35-40.

Sato Y, Taki K, Yoshida H. 1997. Thermal analysis and bond quality of thermosetting resin adhesives (in Japanese). Proceedings of the 35'h Annual Meetings of The Adhesion society of Japan. Tokyo: The Adhesion society ofJppan. Pp. 129-130.

Taki K, Mizumachi H, Yamagishi Y. 1979. Bond quality of PVA-isocyanate reactive resin adhesives (II) (in Japanese). Mokuzai Gakkaishi. 25(3): 216-224.

Taki K, Yamada M, Yoshida H. 1998. Thermal analysis and bond strength of thermosetting resin. Book of abstract the 1st World Congress on Adhesion and Related Phenomena, Germany. Pp. 167

Taki K, Yoshida H, Yamada M. 2001. Thermal analysis and bond quality of phenol-formaldehyde resin adhesives. Proceedings of Wood Adhesive 2000 No.7252. USA: USDA. Pp. 351-355.

Umemura K, Kawai S, Nishioka R, Mizuno Y, Sasaki H. 1995. Curing behavior of wood adhesives under high-pressure steam I, phenolic resin. Mokuzai Gakkaishi. 41(9): 828-836.

Umemura K, Takahashi A, Kawai S. 1998. Durability of isocyanate resin adhesives for wood I: thermal properties of isocyanate resin cured with water. I Wood Sci. 44(3): 204-210.

Vick CB. 1999. Adhesive bonding of wood materials. In: Wood hand book, wood as an engineering material. Madison: Forest products society. Pp. 9-23.




DOI: https://doi.org/10.51850/jitkt.v8i1.505

DOI (PDF): https://doi.org/10.51850/jitkt.v8i1.505.g413

Refbacks

  • There are currently no refbacks.




Jurnal Ilmu dan Teknologi Kayu Tropis Indexed by:

     

 

ISSN: 1693-383              EISSN: 2656-0178